Semi-trailer with walking floor

Fliegl 3-Achs Schubbodenauflieger 92m³

The images shown are archive images; the vehicle may still be in use!

Weights and Dimensions:
Permissible / technical gross weight: 35,000 / 39,000 kg
Permissible / technical payload approx.: 27,548 / 31,548 kg
Permissible / technical aggregate load: 24,000 / 27,000 kg
Permissible / technical fifth wheel load: 11,000 / 12,000 kg
Unladen weight (basic version) approx.: 7,452 kg +/- manufacturing tolerance
Bsdewk Dc Repfx Aipolp

Overall length approx.: 13,800 mm
Overall width max.: 2,550 mm
Overall height approx.: 4,005 mm
Internal length approx.: 13,460 mm
Internal width approx.: 2,470 mm
Internal height front approx.: 2,655 mm
Internal height rear approx.: 2,853 mm
Volume approx.: 92 cbm
Fifth wheel height approx.: 1,130 mm
King pin installation dimension approx.: 1,640 mm
Front corner dimension approx.: 2,040 mm

Chassis Semi-Trailer for Forwarding
Fine-grain steel lightweight welded construction, up to the landing legs, fifth wheel plate with replaceable 2" king pin.
Prepared lashing rings integrated into the floor (max. 13 pairs)
24-ton two-speed landing gear, single-sided operation, straight lower part, without load equaliser
Pull-out ladder at rear
Door retainers on the sides
Wheel chocks with holder
Aluminum side underrun protection
Steel rear underrun protection with wide Fliegl mud flaps
Foldable fender for lighting unit
Quarter shell mudguards
Rear impact protection

Axles & Suspension
BPW disc brake axles
Air suspension
1st axle with automatic lift axle, including forced lowering and start assist, activation via triple brake application

Brake System
Two-line compressed air brake system
Colour-coded line routing for easier servicing
Spring-loaded parking brake
Two fail-safe coupling heads at front, without connecting line
EBS, electronic braking system with EBS socket at the front, no connecting cable
Wheels 385/55 R22.5"

Electrics
24 volt, multi-chamber lights, yellow side LED lighting
2 white position lights at the front
2 white/red lane marker lights at the rear
2 x 7-pin fail-safe sockets at the front, without connecting cables

SB Hydraulics
Hydraulic cylinder with sliding unit integrated in the floor. Dual-circuit hydraulics.
Note: A dual-circuit hydraulic system is required!
Recommended pump capacity:
Capacity: 110 l/min
Pressure: 250 bar
Min. oil tank capacity: 100 l

SB Tipper Body
Aluminum box-type tipper body made from high-grade, wear-resistant material. Front and side walls made from aluminum hollow sections, welded with a wide special reinforcement profile around the top and a special reinforcement frame at the bottom.
Sliding bulkhead for improved unloading of cargo, with reinforced tarpaulin flaps at the bottom.
Rear wall made of aluminum hollow sections as a two-leaf door, split 1/2 to 1/2, framed all round with a special U-profile with stop and rubber seal, fitted with two external rotary bar locks, locked at top and bottom. Rear wall with mechanical safety lock, operated at the rear on the left side in direction of travel. Including a swivelling crossbar at the top.
Standing platform with ladder access on both sides (left/right in direction of travel) and guardrail for opening and closing the roof tarpaulin
Removable, swivelling crossbars for tarpaulin support + tarpaulin support at front bulkhead and at rear wall.
Roll tarp can be stored on one side with two longitudinal tension belts, 3 ratchet tension belts on the side. The tarp is fastened with hooks and rubber ropes at the front bulkhead and above the rear doors; features

El anuncio se tradujo automáticamente y se pueden haber producido errores de traducción.